JSON-LD markup generated by Google Structured Data Markup Helper.

Call (567) 429-1919

Go to…

Subaru

Home / Subaru

We Service and Repair all Subaru cars

  • 2010 Subaru Outback

    Subaru Outback
    Mileage
    205,041
    Service Date
    10/10/2023
    Services Performed
    • Check LF axle. Customer suspects it may be going bad.
    • 1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – LF _9_/32, RF _9_/32, RR _9_/32, RL _9_/32. 3. TIRE ROTATION -No, If "No" – Then when? Check next LOF 4. Preformed basic safety inspection. Job Completed.
    • used trim rivets to secure LF wheel housing
    • Removed and replaced both front axle shafts
     
    Linda K. gave our service a 5 star review on 10/10/2023

  • 2013 Subaru Outback

    Subaru Outback
    Mileage
    76,211
    Service Date
    5/30/2023
    Services Performed
    • Removed and replaced the front brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
    • Removed and replaced the rear brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
    • RR is metal on metal. Front brakes very low. All original brakes. Removed and compressed calipers. All ok. Needs front and rear pads and rotors.
     
    Mary R. gave our service a 5 star review on 6/2/2023

  • 2014 Subaru Legacy

    Subaru Legacy
    Mileage
    126,981
    Service Date
    2/15/2023
    Services Performed
    • A/T Temp HIgh light is on. Multiple lights flashing in IC
    • Diagnosis led to a failed solenoid valve inside the transmission. This was causing all the warning lights. Prepared an estimate for repairs. After repairs verified that the codes no longer returning. adjusted the transmission fluid level. Test drove with no codes returning while testing after repair.
    • completed.
     
    Paul W. gave our service a 5 star review on 2/22/2023

  • 2015 Subaru Forester

    Subaru Forester
    Mileage
    61,720
    Service Date
    4/19/2021
    Services Performed
    • 1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – LF __4/32, RF __4/32, RR _3_/32, RL _3_/32. 3. TIRE ROTATION – Yes / No, If "No" – Then when? 4. Preformed basic safety inspection. Job Completed.
    • Do a thorough inspection of vehicle fluids, tire pressures, lights, etc
     
    Wanda R. gave our service a 5 star review on 4/21/2021

  • 2012 Subaru Forester

    Subaru Forester
    Mileage
    84,402
    Service Date
    5/14/2020
    Services Performed
    • 1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – LF 7/32, RF 7/32, RR 6/32, LR 6/32. 3. TIRE ROTATION – No, If "No" – Then when? Next service. 4. Preformed basic safety inspection. Job Completed.
    • Removed and replaced LR caliper. Cleaned and greased all contact points. Bled the system for air. Test drove to verify brakes worked as they should. Job completed.
    • Removed and replaced the front brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
    • Removed and replaced the rear brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
    • Test drove around the block and noticed the grinding noise as mentioned by the customer. Removed the wheels and checked the brakes and noticed the front pads are down to 1 MM and the rear ones are down metal to metal. Checked the calipers and the pistons were pushing in on all of them. Recommended the customer to have the pads and rotors replaced. Provided with estimate and customer authorized repairs. Diagnostic completed.
     
    Skye M. gave our service a 5 star review on 5/18/2020