After repairs to all brakes made observed noise from wheel bearing. Raised vehicle on lift and determined LF wheel bearing in early stages of failing. Wheel bearing not loose and not a safety concern at this time.
1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – LF __/32, RF __/32, RR __/32, RL __/32. 3. TIRE ROTATION – Yes / No, If "No" – Then when? 4. Preformed basic safety inspection. Job Completed.
BRAKE INSPECTION – Test drive for brake inspection and remove wheels and diagnose the pad life and caliper function. Check and advice.
Battery – [Date of Manufacture – 1/22 ], _464_/600__ CCA Coolant – tests to -34'f but cloudy color Tires – all 6/32" from 2020 starting to crack a little Steering Components – all good and tight Suspension – all look ok. subframe
Removed and replaced the rear brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
Removed LR caliper to removed seized bolt and pin.
Removed and replaced the front brake pads, rotors and hardware. Cleaned and greased all friction points on the caliper chassis, the guide pins and serviced the calipers pistons. Cleaned the brake rotor mating surface on the hub assembly and applied never seize to prevent rust build up. Secured all bolts and torqued them to spec. Test drove and verified no brake pulsations, grinding, squealing, pulling one way or the other while applying brakes. Job completed.
BRAKE SYSTEM FLUSH – Flush the old brake fluid and fill it with new fluid and bleed the system for air.
Coolant flush complete
Complete
Chris @ Ohio Autopmotive had the WHeel Bearing Pressed.
Mabel M. gave our service a 5 star review on 12/28/2023
completed. front camber was at 1.8 degree. adjusted fronts to -.6 and this caused the vibration on accel to become more pronounced. adjusted to 0 degree and vibration got somewhat better. best repair may be to eliminate the lift.
Rob S. gave our service a 5 star review on 12/21/2023
Switch was not plugged in. Re connected and confirmed that buttons work.
Replaced both headlight assemblies with new ones. Reused customer's low beam bulbs. Retainer clips on connectors to turn signal sockets were brittle and broke when removing. The connectors are firmly seated and staying in place now. Would need to source connectors if this becomes a problem longer term.
Todd B. gave our service a 5 star review on 12/16/2023
1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – LF _14_/32, RF _14_/32, RR _16_/32, LR _16_/32. 3. TIRE ROTATION -No, If "No" – Then when? Check next LOF 4. Preformed basic safety inspection. Job Completed.
Found LF wheel bearing very loose. LF lower ball joint has a little movement. Advised to monitor. RF axle carrier bushing very loose.
Front pads 10mm Rear pads 8mm Inside of front rotors very rusty. Caliper service recommended on front brakes.
Complete
complete
complete
complete
complete
LF mud flap installed.
Craig S. gave our service a 5 star review on 12/7/2023
1. Lubricate and checked chassis. Changed oil and oil filter. Checked all fluid levels and topped off fluids that needed topped. Checked the tire pressure to 32 PSi. 2. Tire tread depth – 3. TIRE ROTATION – Yes / No, If "No" – Then when? 4. Preformed basic safety inspection. Job Completed.
Todd L. gave our service a 5 star review on 12/6/2023
battery tested failed. replaced battery. made repairs to the battery cables. recommend replacing the positive battery terminal and crimping new terminals to wire ends.
Fahim r. gave our service a 5 star review on 12/1/2023
Confirmed crank no start. Fuel pump running when key is cycled. No fuel at the engine. Started and ran engine by fueling through intake. Added gasoline to tank, allowed fuel system to prime and ran engine.
Missing wheel cover. This part no longer produced by GM. Recommend set of aftermarket 15" wheel covers or may be able to find one on ebay or at a salvage yard. R&A has several. 3903 County Road 220 Findlay, OH 45840 P: 419-420-0653
Nina P. gave our service a 5 star review on 11/17/2023